Adt Safewatch Pro 3000 Master Code Reset

Adt Safewatch Pro 3000 Master Code Reset Code
Adt Safewatch Pro 3000 Master Code Reset

ADT's corporate installer code is regarded as a trade secret. While various websites have published the code, the surer way to get into a system is the 'backdoor' method. The process of getting into installer programming via the backdoor is different depending on which system you own.Please read the following guide carefully. It will help you determine whether you can reset your ADT alarm system, even if you do not have the installer code.

Identify your system. ADT nearly always uses Honeywell/ADEMCO products when they install in home. Sometimes, however, they use DSC, GE/Interlogix, 2GIG, or another major brand. If your system is a Honeywell or ADEMCO and is wired, then look at the circuit board in the beige box. There will be a half inch by half inch PROM chip on it. It should look something like this:If you see a long rectangular PROM instead of this small, square one, or if your PROM says Safewatch Pro 2000, then you likely have a VISTA 20SE. A Safewatch Pro 3000, however, corresponds with the Honeywell/ADEMCO Vista 20P.

If you have a 20SE, or any of the non-Honeywell panels mentioned above, we recommend sending an email with a picture of the system to support@alarmgrid.com or calling our main phone number (888-818-7728). This is for the commonly installed wired panels.

If you have an all-in-one wireless system, such as the L7000, L3000, or the new Lyric, then go ahead and skip to step 3. If you have a Safewatch Pro 3000, 20P or any other Honeywell panel, then proceed to step 2. Identify your communicator. If your system has been monitored over traditional phone line, and you are looking to have the same setup going forward, then you're ready to go. You probably don't need to add much more to your system.

There are a lot of things you'll miss out on, like the ability to get text and email alerts, or the ability to see your system activity on your phone and computer. But not everybody wants that. If you do have a communicator, we can help you figure out what you need to do next. ADT often uses proprietary communicators. These communicators can usually be identified by the logo they print on the item. Sometimes, however, they use a plain old Honeywell communicator.

If ADT installed a Honeywell communicator such as the iGSMV4G, GSMV4G, GSMX4G, or 7847i, then go ahead and proceed to the next step.If you have a proprietary communicator, then in order to get your system monitored, you will need to get a new system communicator. We recommend the iGSMV4G. This will give you the most options. However, if you just want internet-only communication, the 7847i may work fine for you. Ultimately, the iGSMV4G costs only a little bit more, which we think is worth the benefit. If you have a Safewatch Pro 3000 or if your system's got a PROM chip with the letters WA20P on it, but indicates a revision smaller than 9.12, then you will probably want to change out the PROM chip.

Backdoor into the system. Honeywell systems are simple to backdoor into. We have a simple guide on how to backdoor into your as well as a video. For those who are looking for instructions on how to reset a wireless adt alarm panel, we have other guides that will instruct you on backdooring into them:,. In the case of both VISTAs and Lyrics, there is a way to permanently lock an end user out of programming. If this has been done to your panel, you will have to either have the old provider unlock the panel or do a full panel replacement. Reset the master code.

You will know as soon as you go through the guide. Once you have entered the system's programming through the back door, changing your ADT codes couldn't be simpler. Change the installer codes and ADT master codes to whatever you would like. Resetting the Master code on a Lyric is easy and is basically the same process as any of the LYNX Touch panels. Watching this should give you the steps necessary to make the changes to your L5210 or L7000. Following this guide will get your ADT system up and running so that you can be monitored by any other company.

You do not need the ADT installer code to actually modify the system, and following these steps will not hurt the programming in the panel. Even replacing the PROM should preserve all programming.

If you have any questions about how to reset your ADT alarm panel, feel free to contact us calling the number above or emailing support@alarmgrid.com Did you find this answer useful? We offer alarm monitoring as low as $10 / month. A Safewatch Pro 3000 is an ADT branded VISTA-20P. If you simply want to turn the system off, you would need to disconnect one of the leads going to the backup battery that's inside the beige metal alarm cabinet and then unplug the wall transformer (a beige power supply plugged into a standard wall outlet). Installers often plug the transformer into an outlet that's not necessarily right by the alarm cabinet so you may have to search the house a bit to find the transformer.

Check outlets in the basement, attic, laundry room, utility closet, ceiling of garage, etc.Once you find the transformer, you can also use the information from the FAQ above to change the code if you'd like to just set a new code and then disable the Chime mode instead of fully powering the system down.If you need additional help, please call us or email support@alarmgrid.com. Enter programming. Enter the Installer Code (default is 4112) + 8 + 00. You should either see 20 (fixed keypad) or Installer Code 20 (alpha keypad). If you're unsure of the installer code, you can use the backdoor method to access programming.Remove the phone number.

Enter.41. You should hear three beeps. Enter.42. Again, you should hear three beeps.Program dynamic signaling. Enter.54, followed by #15. Then enter.55, followed by 1.Exit programming. Press.99 to exit system programming.This will get rid of the FC error.